·
2000085
产品目录
点胶机
 
灌胶机
 
点钻机
 
非标点胶机
 
非标设备
 
T8灯管点胶机
 
点胶阀
 
点胶机配件
 
栏目导航
动点胶机怎么调试才能达到最佳运行状态
浏览数:4

自动点胶机怎么调试才能达到最佳运行状态?      

1.将装好胶水的针筒放入针筒夹持器后并固定。比如装AB胶,将A胶和B胶分别从压力桶接到胶枪A、B进胶口,A、B胶分别通过三通到混合管时开始混合,胶水混合程度由混合管长度决定,只需控制压杆即可控制胶水通断,由一连串左右旋叶片相互垂直排列在套管内组成,A、B胶水经过混合管时进行连续的切割与重合为均匀的混合液,以保证出胶量精确。
Put the glue filled syringe into the needle holder and fix it. For example, A glue and B glue are received from the pressure bucket to the glue gun A and the B inlet, and the A and B glue are mixed through three to the mixing tube respectively. The mixing degree of the glue is determined by the length of the mixing pipe. The glue is controlled by the pressure bar only. A series of left and right rotating blades are arranged in the casing, A and B glue. When water passes through the mixing pipe, it is continuously cut and coincident to form a uniform mixture to ensure the exact amount of glue.

自动点胶机

2.连接气阀,将点胶机的点胶控制器口通过气管连接到针筒,并把针筒气阀连接到点胶控制器的AIRIN,并且连接点胶机和点胶控制器的电缆线。
Connect the air valve to connect the nozzle of the glue dispenser to the barrel through the trachea, and connect the pin valve to the AIRIN of the dot glue controller, and connect the cable of the dispenser and the dot glue controller.

3.将点胶机的点胶接口通过电缆线连接到点胶控制器的信号输入接口,把脚踏板连接到点胶机的运行接口上,以控制点胶机的运行。将Z轴的连接电缆插头与点胶机Z轴连接。如所用点胶控制器同点胶机的连接器型号相同,可以根据连接器的芯数不同来看出点胶机的点胶和运行等连接口,二芯点胶,三芯运行。
Connect the spot glue interface through the cable to the signal input interface of the dot glue controller, and connect the foot pedal to the running interface of the glue dispenser to control the running of the glue dispenser. Connect the connecting cable plug of the Z shaft to the Z axis of the dispenser. If the glue controller is the same as the connector model of the glue dispenser, it can be seen according to the different core number of the connector to see the joint of the glue dispensing and operation of the glue dispenser, two core glue and three core running.

4.将手持式编程器通过串口线选择到点胶机左侧的接口上,如果所用点胶控制器同点胶机背面的连接器型号不相同,可以根据点胶控制器的说明书进行电缆线的配制和连接。
The hand-held programmer is selected through the serial port line to the interface on the left of the glue dispenser. If the glue controller is different from the connector on the back of the glue dispenser, the cable can be made up and connected according to the instructions of the dot glue controller.


欢迎留言